The construction of automobile glass film is revealed

[China Glass Network] Automotive film, technology is very important. It is reported that there are only dozens of tools for car foil filming, and there are about 8 steps in the filming process. The filming time of a car takes one and a half hours to two hours to complete. The film is actually very simple, it is difficult to be careful. When choosing the beauty point of the film, the owner must be cautious, because the quality of the relationship film is related to the actual visual effect and service life. Professional car foil shops have special processes and tools. There are at least 13 tools required for each filming process. The tools used only for watering are divided into hard and soft. Before using hard scraping water, apply a protective film to prevent damage to the film before it can be drowned. Because the service process is very important at this time.

1. Observe the installation of the window glass:

Before installation, it is necessary to observe whether the installation of the window glass is complete and the integrity of the automobile glass to ensure the normal operation of the subsequent filming work.

2. Preparation of construction workers and tools:

The construction personnel's dressing not only reflects the personnel management level of the construction unit, but also has an important impact on the construction quality. During the film construction process, the construction personnel must wear uniform tooling and buckle all the buttons. This can avoid the occurrence of scratched paint on the construction process and the scattering of the fibers of the clothes onto the construction surface.

"If you want to do something good, you must first sharpen your tools." The film is no exception. Construction tools that need to be prepared include: wiper blades, pressure watering cans, heat guns (power, wind speed), cutting tools, absorbent towels, fluorescent lamps, tape masking films, and glass cleaners.

3. Cover the necessary parts inside the car to prevent liquid infiltration:

In order to ensure that the sprayed cleaning fluid and lubricating fluid do not affect the in-vehicle electronic equipment during the construction of the automobile thermal insulation film and to ensure the initial state of the interior trim, the necessary requirements for the seat and the instrument panel in the vehicle are required. Covered.

4. Clean the window glass that needs to be constructed:

Cleaning the inside and outside of the window (the focus is on the cleaning of the interior and glass sealant areas). This is mainly to prevent the construction quality problems of dirt or other objects existing between the film and the window glass after the film is applied to ensure that the film and the glass can be perfectly combined.

5. Pre-cutting of the film:

Use a ruler to measure the size of the front and rear windshield glass, including length and width. Select the type of insulation film to be applied from the tool holder and cut it to the size of the windshield glass that has been measured.

6. Dry-bake plastic film (pre-shrinkage):

In order to ensure that the plastic film after shaping can more accurately fit the curvature of the window glass, and at the same time reduce various problems that may be found during the direct wet baking process, it is recommended to first dry the film before wet baking. In order to enable the thermal insulation film to be fully pre-shrinked.

7. Clean the outside of the windshield with a glass cleaner and car wash mud, and spray the mounting liquid:

The main purpose of spraying the mounting liquid is to ensure that the thermal insulation film can achieve better lubrication movement during the construction of the wet baking film.

8. Wet-bake plastic film (volt-adhesive):

After the thermal insulation film has undergone the dry baking operation, the shape of the thermal insulation film is basically consistent with the curvature of the windshield, but in order to further improve the vulcanity of the thermal insulation film, the thermal insulation film needs to be wet-baked. .

9. Cutting the finished film:

In the process of cutting the finished heat-insulating film, a construction worker is required to align the fluorescent lamp in the cab with the edge of the heat-insulating film cutting, because this allows the outsiders to determine the cutting position more conveniently.

10. Clean the inside of the windshield with the cleaning solution and spray enough mounting liquid:

The purpose of spraying the cleaning solution is to avoid dust spots and reduce corrosion on the edges; the purpose of spraying the mounting liquid is to obtain the viscosity required for setting and better construction results.

11. Remove the transparent protective layer from the film and attach the film to the inside of the windshield.

12. Use a wiper blade to squeeze out the mounting solution.

In the process of removing the installation liquid by using the wiper blade, the installation liquid between the heat insulation film and the window glass should be scraped off as much as possible, so that the drying time of the heat insulation film can be reduced, and the better bonding effect and overall performance can be obtained. Visual effect.

Mattress And Pillow Protectors

Aireloom Mattress,Mattress Protector,Waterproof Mattress Cover,Waterproof Mattress Protector

Hangzhou Dowin Hometextile Co.,Ltd. , https://www.dowinbedding.com